- How I create RSA key and enable SSH access in Cisco VG202, in a Cisco router I use the next commands(but in a VG not exists): conf t crypto key generate rsa modulus 1024 ip domain-name domain-name ip ssh version 2 ip ssh time-out 120 ip ssh authentication-retries 3 line vty 0 4 transport input telne.
- Dec 26, 2013 so it looks as if there is no point in the 'crypto key generate rsa' command if i follow it up with the 'crypto key generate rsa usage-keys label sshkeys mod 1024' command, i just wanted to make sure the first wasn't need for the second to work or something screwy like that.
Generate A Rsa Crypto Key
Q: I have a Cisco switch in my network, which I can access by hooking up a console cable directly to the device. I like to access the switch remotely using SSH. How can I enable ssh on my Cisco 3750 Catalyst Switch?
A: By default, when you configure a Cisco device, you have to use the console cable and connect directly to the system to access it. Follow the steps mentioned below, which will enable SSH access to your Cisco devices. Once you enable SSH, you can access it remotely using PuTTY or any other SSH client.
A: By default, when you configure a Cisco device, you have to use the console cable and connect directly to the system to access it. Follow the steps mentioned below, which will enable SSH access to your Cisco devices. Once you enable SSH, you can access it remotely using PuTTY or any other SSH client.
1. Setup Management IP
Crypto Key Generate Rsa
First, make sure you have performed basic network configurations on your switch. For example, assign default gateway, assign management ip-address, etc. If this is already done, skip to the next step.
In the following example, the management ip address is set as 192.168.101.2 in the 101 VLAN. The default gateway points to the firewall, which is 192.168.101.1 Windows 7 microsoft word product key generator.
2. Set hostname and domain-name
When you use the crypto key generate rsa command, it will ask you how many bits you want to use for the key size. How much should you pick? It’s best to check the next generation encryption article from Cisco for this. At this moment, a key size of 2048 bits is acceptable. Key sizes of 1024 or smaller should be avoided. NOTE: “Zeroizing” the switch’s server host certificate or key automatically disables SSL (sets web-management ssl to No). Thus, if you zeroize the server host certificate or key and then generate a new key and server certificate, you must also re-enable SSL with the web-management ssl command before the switch can resume SSL operation.
Next, make sure the switch has a hostname and domain-name set properly.
3. Generate the RSA Keys
The switch or router should have RSA keys that it will use during the SSH process. So, generate these using crypto command as shown below.
Also, if you are running on an older Cisco IOS image, it is highly recommended that you upgrade to latest Cisco IOS.
4. Setup the Line VTY configurations
Setup the following line vty configuration parameters, where input transport is set to SSH. Set the login to local, and password to 7.
If you have not set the console line yet, set it to the following values.
5. Create the username password
If you don’t have an username created already, do it as shown below.
Note: If you don’t have the enable password setup properly, do it now.
Make sure the password-encryption service is turned-on, which will encrypt the password, and when you do “sh run”, you’ll seee only the encrypted password and not clear-text password.
5. Verify SSH access
From the switch, if you do ‘sh ip ssh’, it will confirm that the SSH is enabled on this cisco device.
After the above configurations, login from a remote machine to verify that you can ssh to this cisco switch. Key generator for any software, free download.
![Generate Generate](/uploads/1/2/6/0/126085268/811845441.jpg)
In this example, 192.168.101.2 is the management ip-address of the switch. https://celestialtwitter356.weebly.com/blog/windows-vista-product-key-generator-free-download.
> Add your comment
If you enjoyed this article, you might also like.
Next post: How to Backup Oracle Database using RMAN (with Examples)
Previous post: How to Use C++ Single and Multiple Inheritance with an Example